Jacuzzi OPTICATM 300 Manual do Utilizador descarregar pdf

OPTICA

™

300

SHOWER MIXER/TRANSFER VALVE

INSTALLATION INSTRUCTIONS

INSTALLER: LEAVE THIS INSTRUCTION MANUAL FOR OWNER'S/USER'S REFERENCE

WARNING: This system/device must be set by the installer to ensure safe, maximum temperature. Any change in

the setting may raise the discharge temperature above the limit considered safe and may lead to scalds.

CAUTION: As the installer of this valve, it is your responsibility to properly install and adjust this valve per the

instructions given. This valve does not automatically adjust for inlet temperature changes, therefore, it is necessary

to adjust the Rotational Limit Stop at the time of installation. You must inform the owner/user of this requirement by

following the instructions below. After installation and adjustment, you must write in the temperature and the date

you adjusted the Rotational Limit Stop on the warning label provided and apply or attach it to the hot water heater.

Be sure this instruction sheet is delivered to the owner/user.

WARNING: This pressure balanced bath valve is designed to minimize the effects of outlet water temperature

changes due to inlet pressure changes, commonly caused by dishwashers, washing machines, toilets and the like.

It may not provide protection from scalding when there is a failure of other temperature controlling devices elsewhere

in the plumbing system if the Rotational Limit Stop is not properly set, or if the hot water temperature is changed after

the Rotational Limit Stop is set, or if the water inlet temperature changes due to seasonal changes.

OPTICA 300

FINISHING WALL

TILE (FINISH SURFACE)

FACEPLATE (SEALANT NOT PROVIDED)

TRIM SLEEVE OF TRANSFER VALVE

GASKET

TRIM SLEEVE

2-3/8" DIA.

WOOD CROSS MEMBER

REAR VIEW

(FRONT HAS RED

AND BLUE DOTS)

GASKET

COPPER PIPE (NOT PROVIDED)

REAR VIEW

SEALANT (SILICONE) ON BACKSIDE OF

FACEPLATE

FEMALE THREAD TO SWEAT ADAPTOR

(NOT PROVIDED)

LEFT-HAND THREAD TO

SWEAT ADAPTOR (NOT PROVIDED)

4-15/16" MINIMUM

SEALANT (100% SILICONE) ON BACKSIDE OF

FACEPLATE (SEALANT NOT PROVIDED)

NOTE: WHEN INSTALLING BAND, RING, ROPE

OR FACETED HANDLE, PULL TRIM SLEEVE OUT

TO MEET HANDLE.

PLASTER GUARD

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - INSTALLATION INSTRUCTIONS

OPTICA™ 300SHOWER MIXER/TRANSFER VALVEINSTALLATION INSTRUCTIONSINSTALLER: LEAVE THIS INSTRUCTION MANUAL FOR OWNER'S/USER'S REFERENCEWARNING

Página 2

INSTALLATION INSTRUCTIONSWARNING: Failure to follow these instructions could prevent the mixer/transfer valve from functioning properly.1. Shut

Página 3 - Rotational Limit Stop

9. Flush your system prior to installing the shower head. Place handle on valve stem and turn handle to full mix position. Turn ON water s

Página 4

Faucet leaks from bath spout/showerhead – SHUT OFF WATER SUPPLIESReplace seats and springs – Repair Kit RP4993. Check conditions of lower o-rings an

Página 5

1st Position2nd Position 50 70 50 70 70 70 40 853rd Position 61 79 67 83 74 89 70 1014th Position 68 83 75 90 84 97 84 1105th

Página 6 - This page left blank

Comentários a estes Manuais

Sem comentários

Jacuzzi OPTICATM 300 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Loiças sanitárias Jacuzzi OPTICATM 300. Jacuzzi OPTICATM 300 User's Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Loiças sanitárias Jacuzzi OPTICATM 300